Comments on: Octaver Clone http://gaussmarkov.net/wordpress/circuits/octaver-clone/ guitar stompboxes and electronics Thu, 17 May 2012 02:09:15 -0700 hourly 1 http://wordpress.org/?v=3.1 By: André http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1627 André Sun, 22 Apr 2012 23:32:35 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1627 Well, not only in 0... it is there all the time, but it gets less perceivable as the octaves and direct volumes are increased. Well, not only in 0… it is there all the time, but it gets less perceivable as the octaves and direct volumes are increased.

]]> By: André http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1626 André Sun, 22 Apr 2012 23:31:11 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1626 Hi! Just built this really nice circuit (used a madbean pcb), but I am getting bleedover signal when I set everything to 0. There are no wires over or under the circuit board, and the FX I/O are shielded. It is not really loud, but quite fuzzy. I used the audioprobe to check a few points, and when I touch lead n.3 of the clean vol, which would be the first thing to be amplified according to the schematic, I am already getting those signal in the mix. Tried chaning the pots values just to see if that would make a difference, but nothing. Does anyone also had a similar problem? Tks! Hi! Just built this really nice circuit (used a madbean pcb), but I am getting bleedover signal when I set everything to 0.

There are no wires over or under the circuit board, and the FX I/O are shielded.

It is not really loud, but quite fuzzy.

I used the audioprobe to check a few points, and when I touch lead n.3 of the clean vol, which would be the first thing to be amplified according to the schematic, I am already getting those signal in the mix.

Tried chaning the pots values just to see if that would make a difference, but nothing.

Does anyone also had a similar problem?

Tks!

]]> By: Elliot http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1500 Elliot Tue, 22 Mar 2011 01:16:19 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1500 Hi, I've been looking around trying to find a normal layout (without SMD) due to me trying this (gauss) layout multiple times and failing every time... I found people talking about Mundy's layout, and I'm wondering if anyone knows where I could find that. I found some dead links, but other than that-Anyone have any suggestions? Thanks so much! Hi, I’ve been looking around trying to find a normal layout (without SMD) due to me trying this (gauss) layout multiple times and failing every time…
I found people talking about Mundy’s layout, and I’m wondering if anyone knows where I could find that. I found some dead links, but other than that-Anyone have any suggestions?
Thanks so much!

]]> By: Mário Calegaro http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1229 Mário Calegaro Mon, 09 Nov 2009 20:06:52 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1229 Maybe you can give some tips... I own an original OC-7, and his octave up doesn´t work anymore... Any advice? Have you seen this before? Thank you and congrats! Ps.: I´m an eletronics technician that doesn´t work with eletronics since the trainee passage. Maybe you can give some tips… I own an original OC-7, and his octave up doesn´t work anymore… Any advice? Have you seen this before? Thank you and congrats!

Ps.: I´m an eletronics technician that doesn´t work with eletronics since the trainee passage.

]]> By: diego http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1026 diego Mon, 16 Feb 2009 19:39:26 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1026 Is there a bigger version of this project? with ICs of normal dimensions? thanks,Diego Is there a bigger version of this project? with ICs of normal dimensions?

thanks,Diego

]]> By: zeta55 http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1023 zeta55 Sat, 07 Feb 2009 10:49:01 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1023 diego, you're right. The projekt files were edited after my first build. There were a few corrections made. /Krister diego, you’re right. The projekt files were edited after my first build. There were a few corrections made.

/Krister

]]> By: diego http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-1021 diego Fri, 06 Feb 2009 00:15:06 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-1021 is the pcb layout in the photograph the same of the project? i'm curious because the position of the components in the photo is different from the layout... is the pcb layout in the photograph the same of the project? i’m curious because the position of the components in the photo is different from the layout…

]]> By: js http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-891 js Fri, 01 Aug 2008 10:53:12 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-891 Does anyone have a DIP layout or pcb? I realy don't like to hand solder SMD chips and i'm no expert in Eagle :) Does anyone have a DIP layout or pcb? I realy don’t like to hand solder SMD chips and i’m no expert in Eagle :)

]]> By: gaussmarkov http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-144 gaussmarkov Fri, 16 Nov 2007 05:01:05 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-144 Finally ... I changed IC2 to an LM324. I apologize for the delay. Finally … I changed IC2 to an LM324. I apologize for the delay.

]]> By: zeta55 http://gaussmarkov.net/wordpress/circuits/octaver-clone/comment-page-1/#comment-87 zeta55 Wed, 24 Oct 2007 06:23:11 +0000 http://gaussmarkov.net/wordpress/circuits/octaver-clone/#comment-87 I noticed that IC2 on the board2 schematic and layout calls for a TL074. In my pedal I have a LM324 in that position. If it matters I don't know. I noticed that IC2 on the board2 schematic and layout calls for a TL074. In my pedal I have a LM324 in that position. If it matters I don’t know.

]]>